Research on Biomedical Engineering
http://www.rbejournal.periodikos.com.br/article/doi/10.1590/2446-4740.0710
Research on Biomedical Engineering
Original Article

Fretting corrosion tests on orthopedic plates and screws made of ASTM F138 stainless steel

Santos, Claudio Teodoro dos; Barbosa, Cássio; Monteiro, Maurício de Jesus; Abud, Ibrahim de Cerqueira; Caminha, Ieda Maria Vieira; Roesler, Carlos Rodrigo de Mello

Downloads: 0
Views: 909

Abstract

Introduction: Although there has been significant progress in the design of implants for osteosynthesis, the occurrence of failures in these medical devices are still frequent. These implants are prone to suffer from fretting corrosion due to micromotion that takes place between the screw heads and plate holes. Consequently, fretting corrosion has been the subject of research in order to understand its influence on the structural integrity of osteosynthesis implants. The aim of this paper is to correlate the surface finish characteristics of bone plate‑screw systems with fretting corrosion. Methods: The surface finish (machined and polished) of five specimens taken from three commercial dynamic compression plates (DCP) were evaluated. For testing, the specimens were fixed with bone screws, immersed in a solution of 0.90% NaCl and subjected to a rocking motion with an amplitude of 1.70 mm and frequency of 1.0 Hz for 1.0 × 106 cycles, according to the ASTM F897 standard. Both, plate and screws were manufactured in Brazil with ASTM F138 stainless steel. Results: Flaws on the hole countersink area and on the screw thread of some specimens were identified stereoscopically. At the end of the test all the specimens showed evidence of fretting corrosion with an average metal loss of 4.80 mg/million cycles. Conclusion: An inadequate surface finish in some areas of the plates and screws may have favored the incidence of damage to the passive film, accelerating the fretting corrosion at the interfaces between the plate hole countersink and the screw head.

Keywords

Osteosynthesis, DCP, Bone plate, Screw, Fretting corrosion, Stainless steel.

References

American Society for Testing and Materials - ASTM. F138-13a: Standard Specification for Wrought 18Chromium-14Nickel-2.5Molybdenum Stainless Steel Bar and Wire for Surgical Implants. West Conshohocken: ASTM; 2013a

American Society for Testing and Materials - ASTM. F897-02: Standard test method for measuring fretting corrosion of osteosynthesis plates and screws. West Conshohocken: ASTM; 2013b

Billi F, Benya P, Ebramzadeh E, Campbell P, Chan F, McKellop HA. Metal wear particles: what we know, what we do not know, and why. SAS Journal. 2009; 3(4):133-42. http://dx.doi.org/10.1016/j.esas.2009.11.006. PMid:25802639

Brown SA, Merritt K, Payer JH, Kraay MJ. Fretting corrosion of orthopaedic implants. Pennington: The Electrochemical Society; 1994. p. 42-47

Brown SA, Merritt K. Fretting corrosion of plates and screws: an in vitro test method. In: Fraker AC, Griffin CD, editors. Corrosion and degradation of implant materials. Philadelphia: American Society for Testing and Materials; 1985. p. 105-16. ASTM STP, 859

Gilbert JL, Jacobs JJ. The Mechanical and electrochemical processes associated with taper fretting crevice corrosion: a review, Modularity of Orthopedic Implants. ASTM Special Technical Publication. 1997; 1301:45-59

Hoeppner DW, Chandrasekaran V. Fretting in orthopaedic implants: a review. Wear. 1994; 173(1-2):189-97. http://dx.doi.org/10.1016/0043-1648(94)90272-0

Kanchanomai C, Phiphobmongkol V, Muanjan P. Fatigue failure of an orthopedic implant: a locking compression plate. Engineering Failure Analysis. 2008; 15(5):521-30. http://dx.doi.org/10.1016/j.engfailanal.2007.04.001

Kumar S, Narayanan TSNS, Raman SGS, Seshadri SK. Evaluation of fretting corrosion behavior of CP-Ti for orthopaedic implant applications. Tribology International. 2010; 43(7):1245-52. http://dx.doi.org/10.1016/j.triboint.2009.12.007

MacLeod AR, Simpson AHRW, Pankaj P. Reasons why dynamic compression plates are inferior to locking plates in osteoporotic bone: a finite element explanation. Computer Methods in Biomechanics and Biomedical Engineering. 2015; 18(16):1818-25. http://dx.doi.org/10.1080/10255842.2014.974580. PMid:25473732

Miller DL, Goswami T. A review of locking compression plate biomechanics and their advantages as internal fixators in fracture healing. Clinical Biomechanics (Bristol, Avon). 2007; 22(10):1049-62. http://dx.doi.org/10.1016/j.clinbiomech.2007.08.004. PMid:17904257

Sargeant A, Goswami T. Hip Implants – paper vi – ion concentration. Materials & Design. 2007; 28(1):155-71. http://dx.doi.org/10.1016/j.matdes.2005.05.018

Uhthoff HK, Poitras P, Backman DS. Internal plate fixation of fractures: short history and recent developments. Journal of Orthopaedic Science: Official Journal of the Japanese Orthopaedic Association. 2006; 11(2):118-26. http://dx.doi.org/10.1007/s00776-005-0984-7. PMid:16568382

Virtanen S, Milosev I, Gomez-Barrena E, Trebse R, Salo J, Konttinen YT. Special modes of corrosion under physiological and simulated physiological conditions. Acta Biomaterialia. 2008; 4(3):468-76. http://dx.doi.org/10.1016/j.actbio.2007.12.003. PMid:18226986

Weinstein AM, Spires WP, Klawitter JJ, Clemow AJT, Edmunds JO. Orthopedic implant retrieval and analysis study. In: Syrett BC, Acharya A, editors. Corrosion and degradation of implants materials. Philadelphia: American Society for Testing and Materials; 1979; p. 212-28. ASTM STP, 684
5889fbf35d01231a018b487e rbejournal Articles
Links & Downloads

Res. Biomed. Eng.

Share this page
Page Sections